Just see the photo and i'm sure you all know what to do.... :D


I used NT cutter for plywood and perspect cutter for clear perspect

Make sure your stand stick vertically(clear epoxy will do)

Mask clear plastic and apply body putty on the plywood base,let it dry and send it off

Apply 1st primer and fill small hole and uneven surface with tamiya putty

2nd sending will need, to make it smoth than apply last primer

Paint it with flatblack or what ever colour you like

Take out the masking tape

And your aircraft is flying now.... :lol: :lol: :lol: Selamat Mencuba..... :D

MY TWO CENTS JE
dremel

Wah... very nice how-to and very good picture taking... nampak macam betul2 terbang... hehehehe... Good job... ;)

oh thanks, dremel for the simple HOW TOs...
ow where's my raw material...

Mat Lobang,

Hang memang hebat!! Thanks for the tip.

Sarge.

Hai guys.,

druid99-thank you very much,aku ingat join SMM nak improvekan aku punya skill je...tapi nampaknya fotografi,knowledge dan english pun aku kena improvekan jugak...... :lol: :lol: :lol:

koowwilliams-so dont throw any unused plywood ok... :lol:

Bud Bilko-thanks.... :) just my two cents ja Bud.... :D


dremel

Rasanya photography dah ok dah Naza... gambar last sekali dengan aircraft tu nampak real... bayang2 tak nampak and nampak macam takde support pun... Cuma kena rajin2 lah ambik gambar progress and rajin2 lah post kat sini... hehehe

Your english pun so far so good. Takde yang tak faham pun dalam ni rasanya.... :)

Thank you so much Im....i will...i will...... :D

dremel

Naza,
ko guna plywood 2mm ke??
ko potong pakai ape beb??

err .. may i ask, the clear perspect , is it sold in hardware shop or ???

some hardware shop do stock it..but very limited

some art supply store do have a few..

you can get it from yellowpages..look for perspex supplier

ooo... camtu simple je ye... but how do u usually fix the jet to the top of the stand? permanent or temporary joints? glue or screws? do u drill holes underside of the aircraft? any pics? fuhhh banyak soalan aku ni :rolleyes:

sifu dremel....aku potong plastik patah da....ape razor yg sesuai? n what kind of plastic yg ok? aku punye plastic lembek semacam la.

Silantra- plywood 3mm, you can cut by using a normal cutter, slice it and bend it abit, slice a few more times to cut it. Always cut out of the line first, and folow by cuting closer to the line that you want.

kwongyan- I bought it at Toh Plastic , Jln Tun Razak, tel-03-40417549, ask for location. I alway bought hight impact plastic from them, when i was there i'll ask the taukeh for left over perspect thats he dont want. Sometimes i got it free, as for a big pice he will ask for 3-4 ringit. hehehe

moJimbo- i would like to put it temporary, just slot it in. yup kena drill lubang. pics kena tunggu next a.craft-F-15J White Dragon.
I know sometimes i feel sayang to drill the hole, but what you can do is, spray a normal sticker with a same color as a belly, cut it slightly biger than the hole and stick it on if we want to display it without stand.



2 cents

Naza

okay.... i'm looking fwd to the pics, tq. :)

What kind of plastic u meant?....u can use a normal blade for high impact plastic. As for a perspect i used perspect cutter.

ape yg sebenar ni yang lembik semacam ni?....ish u ni bro, wat suspen je :rolleyes: :lol:

Razman, kau pakai plastik untuk transparency ke yang lembik semacam tu? Hehehe...

Rasanya kalau perspex tu, kena cari yang tebal sikit macam dalam 1mm to 1.5mm, betul tak Naza?

perspect 1mm too thin bro takut goyang2., TA-4PTM i used 2mm, Air to Air Dio 3mm or 4mm tak sure.

2mm is easier to cut with perspex cutter. 3mm and above we need dremel machine disc.

bro,
kasi tunjuk macamana perspex cutter bro....

i got the normal V cutter ..potong pelan2 then kepak kasi putus... that's my method

Sil...that is the one i usedlah bro....v cutter....aku selalu namakan tools ikut suka hati aku :lol: :lol: :lol:

Method pon betul....but dont try to cut a difficult shapelah....as for a display stand just make it straight.....senang potong....

Bro,

apa itu V cutter , boleh tunjuk gambar?

thomas,
some called it P cutter...

it look something like this


so many brands out there, olfa, tamiya..
i used the one specifically for perspex..forgot the brand but the blade is thinner.. means smaller v groove

yup yg inilah V cutter master.....thanks sil.... ;)

ooohhhh aku dah paham... yang tebal ye? tadi aku tengok kat bawah meje manager aku ada base transparent plastik baiiikkkk punye...hahahahaha. nanti ko.
ape lak suspen sifu...tu name nye aku jujur n berterus terang.. <_<

bro, kt atas plastik tu ada 2 btg besi ke & cemana nk cucuk kt tgh2 plastik tu?

Naza this is a quick, cheap and simple way to make a great stand. Many thanks for this excellent tip.

I'm going to pindah this to the aircraft section and pin it as I'm sure many modellers would find this very useful.

yup....glue a small piece clear perspex as you can see there. drill 2 hole and copper rod and slot it in.

razmanosaurex-yeah bro make it cheaper, if u jumpa kat tepi jln any kind of plastic or rod, make sure to keep it....its ight usefull for our hobby...ehe

beachbum- Thanks so much bro....i appreciate it ;)

tq very much for the info.....will try to do it myself

naza
better bukak class la
kenakan fee skit

naza sifu...aku dah follow tips hang. cume aku ubah sikit la..tq

azlandiver,razmanosaurex,- slamat mencuba...btw...that is just a guide line...there're so many way to works with it, as a base u can change it to clear perspec, plaster of paris with your own design, u can buy a jelutong wood from multifilla as a base, infact we can forget about the base, just drill hole to your tv or kayu jati cabinet and put the stand on... :lol: :lol: :lol:

as a stand, u can use copper rod, hight impact pastic, creat ur own design, clear rod, kat toh plastik ada banyk jual and very cheap, etc...

mazrilhisham- nolah bro....saya takda bakat utk mengajar, no skill in comunications thou......btw if 1 day, people really think what i've now is worth it to learn....mybe i try to write a book about what i think about modelmaking/scratchbuilding and how to start it from zero/cheap, simple metematik,...all kampung style.... :D .

Regards
Naza K Dremel